Exactly How To Install A Bath Tub (For Novices).
Exactly How To Install A Bath Tub (For Novices).
Blog Article
What are your opinions on How to Install a Bathtub?
Setting up a tub isn't precisely rocket science, however it does need solid plumbing, woodworking, and also occasionally, tiling skills. Replacing an old bathtub with a new one is also a moderately challenging job. If the old bathtub is conveniently easily accessible, the job can relocate immediately; if you need to open up a wall surface to eliminate the old bathtub as well as place the brand-new bath tub, the job is a lot harder. In either instance, the job is within a residence handyman's abilities, although you will certainly require an assistant to leave the old bathtub as well as embeded in the brand-new one. Make certain you have actually certified yourself for the task as well as fit trying it. Instead of employing a specialist to take control of a halfway-completed job, it is much better to think about employing one before you begin. Chances are you might require an expert plumber to make tube links.
This short article will certainly assist you set up a new bath tub in your washroom if you have actually already bought a brand-new bathtub as well as don't need to transform the plan of your previous water system pipelines.
Your devices and also product list must make up the following:
Preparing for the Installment
First of all, the supporting framework supplied with the bathroom ought to be fitted (if called for) according to the maker's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is very important to ensure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps device to avoid strain on the bath tub.
Fit the versatile tap adapters to the bottom of the two faucets utilizing 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you utilize all of the provided washing machines.
Connect the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must currently prepare to be fitted in its last position.
Removing Old Touches
If you require to replace old faucets with new ones as a part of your setup, then the first thing you ought to do is separate the supply of water. After doing so, turn on the faucets to drain pipes any type of water continuing to be in the system. The process of eliminating the existing faucets can be fairly problematic because of the limited access that is commonly the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the taps. Have a fabric all set for the remaining water that will come from the pipelines. As soon as the supply pipes have been eliminated, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this process. When the faucets have actually been removed, the holes in the bath/basin will have to be cleaned up of any kind of old securing compound.
Before carrying on to fit the brand-new faucets, compare the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Mounting the Tub
Making use of both wood boards under its feet, place the bathtub in the needed setting. The wood boards are handy in evenly spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto 4 little factors.
The next goal is to guarantee that the bath tub is leveled all round. This can be attained by examining the spirit level and adjusting the feet on the bathtub until the level reviews degree.
To mount faucets, fit all-time low of the outermost adaptable faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the exact same for the various other tap.
Turn on the water supply and check all joints and also brand-new pipework for leaks as well as tighten them if required. Fill up the bathtub and also check the overflow electrical outlet and also the regular electrical outlet for leakages.
Lastly, repair the bath paneling as defined in the supplier's user's manual. Tiling as well as sealing around the bath tub needs to wait up until the tub has been used at least when as this will settle it right into its last setting.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the tap and the various other end supplies a connection to the current supply pipes.
If you need to fit a monobloc, after that you will call for lowering couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, position the faucet in the installing opening in the bath/basin guaranteeing that the washers remain in location between the faucet as well as the sink. Secure the faucet in place with the manufacturer given backnut. When the faucet is safely in position, the supply pipes can be attached to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with typical tap ports. The former kind ought to be connected to the faucet finishes first, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the location where the bath satisfies the floor tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to split a rigid seal, triggering the water to penetrate the wall surface between the bathroom as well as the tiling, leading to issues with wetness and feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your components as well as installations. They are marketed in tubes and cartridges, and also are capable of sealing voids up to a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always fill up the bath tub with water before sealing, to permit the movement experienced when the bathtub remains in use. The sealant can break rather early if you do not take into consideration this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally quickly available on the market. It is advisable to fit the tiles using water-resistant or waterproof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm certainly very involved in How to Install a Bathtub Yourself and I'm hoping you appreciated my entry. If you appreciated our blog post if you please do not forget to pass it around. Thanks for going through it.
Book Today! Report this page